- Client Profile: Our client, a reputed Engineering and Construction Company in the Middle East has an upcoming oil and gas project in Algeria. They are presently in need of design and engineering personnel as per following details.
- Prepare / Endorse FEED documents
- Check & review Material Selection Philosophy
- Check & review Corrosion Control Philosophy
- Simulations for corrosion rate calculations
- Check & review Material Selection Diagrams
- Check & review CC & CP requirements
- Interact with vendors during offer evaluation
- Vendor drawing reviews
- Participate in HAZOP/Design Reviews and close outs
- Support during field engineering
- Job-specific skills required:
- Preparation & review of FEED documents
- Pre-bid Engineering
- Checking & review Detailed Engineering deliverables
- Material selection and Corrosion rate calculations.
- Should be conversant with: API / NACE / NFPA / Shell DEP / ASTM / ASME / ISO / NEMA etc
- Prepare and develop process deliverables such as PFDs, P&IDs, Process Data Sheets, Process Design Criteria, Design of relief and venting systems etc.
- Prepare Sizing Calculations such as Equipment Sizing, vessel sizing, Safety & relief valve sizing, Control Valve Sizing, Pump Hydraulic Calculations, Line Sizing
- Be familiar with Process simulation using HYSYS and Hydraulic analysis.
- Prepare datasheet for Equipments and Instruments.
- Prepare Utility Summary, Chemical Summary, Line List, Tie-in List and Equipment List
- Provide the process data for all type of process instruments like pressure, flow, temperature instruments etc.
- Provide process data to piping for valves, heat tracing, other special items datasheet
- Review the vendor documents and ensure that vendor document is in-line with contractual requirement and company specification
- Prepare documents and reports such as Process Description, Heat & Mass Balance, Process Design basis, Line list, Tie-in list, Equipment list, Utility summary, Operating & Control philosophy, Start-up & Shutdown Philosophy, Safeguarding Philosophy, Cause & Effect Diagram, and Relief & Blow down Philosophy etc.
- Engineering, Procurement and Commission
- Preparation of FEED documents
- Pre-bid Engineering
- Preparation of Detailed Engineering deliverables
- Equipment design and process engineering calculations.
- Should be conversant with: API / NACE / Shell DEP
- Prepare and develop Loss Prevention deliverables such as PFD's, P&IDs, Process Data Sheets, Fire Fighting and safety Equipment Datasheets, Specification, Philosophys, Hydrant & Monitor location layout, Fire Fighting and Safety Equipment Layout, Escape Route and Safety Signs Layout, Passive Fire Protection Layout, Fire Water Line List, Fire & Gas Cause & Effect Matrix, Passive Fire Protection Schedule and Hazardous Area Classification Schedule etc.
- Prepare firewater demand and hydraulic calculation reports using PIPENET or equivalent software.
- Prepare and provide inputs to P&ID markups for Firewater ring main system and Deluge system including providing details of interconnection with hose reels, monitors, hydrants, Sprinkler System and deluge valves / nozzles.
- Prepare Fire fighting, safety equipment, clean agent system and emergency response vehicle material requisitions, TQ/ clarification and TBE.
- Review vendor and subcontractor submittals, checking for compliance with project specifications and providing comments as necessary.
- Check final vendor and subcontractor data manuals to ensure that all requested data has been received and approved.
- Prepare safety study scope of work, TQ/clarification, TBE and methodology.
- Participate safety workshops (such as HAZID/HAZOP/SIL) and provide inputs to safety study consultants.
- Coordinate safety study close outs and prepare safety study close out reports.
- Review third party safety study reports that are in compliance with project specifications.
- Prepare / Maintain safety study HSE Action Tracking Register
- Participation in Plot Plan Review and 3D Model Review Workshop to ensure that firefighting and safety equipment locations meet the project requirement.
- Perform conceptual, FEED, safety Studies, and detailed analyses and design as per design basis, project specifications, design codes and standards.
- Clearly communicate and explain complex issues and work to establish understanding.
- Perform design verification through single-discipline check / inter-discipline check (IDC).
- Provide inputs to other discipline, vendor and safety studies consultants as required.
- Provide technical direction and review of Designers producing drawings/documents related to Fire Protection & Safety Engineering.
- Raise technical queries to obtain missing information, clarify work scope, and to maintain preferred Company/project procedures, specifications, standards, practices and operational requirements.
- Identify changes to scope and promptly raise change notifications, including providing any necessary supporting documentation and estimates. Provide similar support for Variation Orders
- Participate in internal, Customer and third party technical audits on engineering deliverables and vendor documents.
- Be familiar with International Standards NFPA, Shell DEP, IP, API,BS And UL/FM for Fire Protection/Detection System and Sonatrach Algeria company Standards & Specification.
- Preparation of Detailed Engineering deliverables
- Should be conversant with International Standards NFPA, Shell DEP, IP, API, BS and UL/FM etc.
- Preparation of FEED documents
- Pre-bid Engineering
- Preparation of Technical Specifications, Design calculations
- Stress Analysis
- Support Engineering
- Datasheets preparation for valves and Specialities
- MTO preparation
- Checking of Drawings.
- Preparation of Technical Specifications and Design calculations
- Power Plants / Oil & Gas / Petrochemical & Refinery / PIPE LINE
- Plot plan, Equipment layouts, Piping layouts
- Detailed engineering drawings
- Design Calculations, Stress Analysis
- Technical Specifications, MR, TBA, PORN, Erection Tender
- Review of Vendor / Other discipline Drawings
- MTO & Datasheets
- Piping Material Specification
- 3D Model review
- Should be able to develop Plot Plan, Equipment Layout and Piping Layouts.
- Should give instructions to Draftspersons and check drawings prepared by them.
- Knowledge of Codes and Standards essential
- Scheduling, Man hour control, Quality, Problem Solving, Drafting in CAD. Knowledge of Codes and Standards essential.
- Power Plants / Oil & Gas / Petrochemical & Refinery / PIPE LINE
- Plot plan, Equipment layouts, Piping layouts
- Detailed Engineering Drawings
- Isometrics drawings, Nozzle Orientation & Vessel Clip Drawings
- Civil Information Drawings
- Support drawings & support schedule
- 3D Model Reviews (30%, 60% & 90%)
- Vendor drawing review & other discipline drawings review
- AutoCAD, Micro-station
- PDS / PDMS / SP3D (ANY ONE)
- Static equipment Design, Preparation of datasheets MR, TS, TQ, TBE, VDR, review of vendor drawings & documents.
- Packages - Prepare datasheets, MR, TS, TQ, TBE, and VDR, review of vendor drawings & documents for Packages being handled.
- Exposure in International Codes and standards (ASME, API, BS, WRC & Equipment handbooks, etc.).
- Static Engineer - Pressure vessel, Heat transfer Equipments & Static packages
- Hands on experience for Static Equipment (Vessel, Exchangers {Shell & Tube, Air Cooler, Plate type}, Filters, Pig launcher/Receiver).
- Package Equipment experience (Separator, Flare package, Burn pits, Water treatment & utility packages).
- FEED / Detailed Engineering / Tender Engineering Skills
- Scheduling, man hour controls and document quality and approval
- Inter Discipline Interaction / Co-ordination.
- Co-ordination with client & Site.
- Coordinating for Hazop & Safety study for the packages.
- Reviewing 3D Model and coordinating with package vendor and inter discipline.
- Exposure in International Codes and standards
- Engineering Software Usage Skills (PV Elite, COMPRESS, Codecal, FEPipe, etc.)
- QMS Adherence.
- Preparation of spec & data sheet for HVAC, AHU, AWU, Chillers, cooling tower and duct sizing & layout etc. for Plant and non-plant buildings.
- Should have exposure in International codes like ASHRE, SMACNA, NFPA, etc.
- Design of Building Heat Load /cooling load calculations.
- Selection of equipments based on heat load calculations.
- Air balance calculation of Buildings.
- Chiller package design and detailing.
- Preparing ducting design and layout using AutoCAD/micro station, etc.
- Review of vendor P& ID, Control diagrams etc
- Building pressurization design, smoke extraction design.
- Wet and Dry ventilation design.
- Green building design, energy density calculation, Good knowledge in ESTIDAMA requirements.
- Sound Knowledge in preparation of manual design calculation.
- Preparation data sheet for HVAC, High side equipments, SOQ for low side equipments.
- FEED / Detailed Engineering / Tender Engineering Skills.
- TBE, VDR. Scheduling , man hour controls and document quality and approval
- Inter Discipline Interaction / Cooperation
- Inter Discipline Vendor / Sub contractor
- Co-ordination with client and site.
- Good knowledge in site Installation & subcontractor management.
- QMS Adherence
- Awareness on 3D Modeling.
- Good working knowledge of various international design standards
- Analysis and Design of RCC/steel Superstructure and Sub-structure
- Documentation of design Calculations as per project requirement
- Drawing & design Checking
- 3D Model review to check fitment of designed structure & for clashes
- Quality Conformance
- Guiding and training juniors to enhance productivity
- Taking review of work done by juniors and reporting to in line manager
- Detailed Engineering, Proposal Engineering, Managing Quality
- Concrete Analysis & Design
- Steel Analysis & Design
- Dynamic Analysis & Design
- International Standards Exposure
- Software Exposure
- Estimation Pre-bid
- Experience of 3D Modelling review software
- Good working knowledge of various international design standards
- List down all the input requirements for the given task
- Analysis and Design of RCC/Steel Superstructure and Sub-structure
- Documentation of design Calculations as per project requirement
- Drawing & design Checking
- 3D Model review to check fitment of designed structure & for clashes
- Quality Conformance
- Analysis & Design
- Other Skills:
- Concrete Analysis & Design
- Steel Analysis & Design
- Dynamic Analysis & Design
- International Standards Exposure
- Software Exposure
- Quantity Estimation & Material take off
- Awareness on 3D Modelling Review software
- Thorough knowledge of Auto Cad for drawing preparation
- Detailing of RCC & Steel structures, Earth works & UG services
- PDS/PDMS knowledge for modelling of RCC & Steel structure
- Drawing Extraction and Detailing of steel structures using TEKLA / PDS / PDMS interface
- Conceptual knowledge of steel connection detailing
- Work planning/allocation among drafting team & monitoring same for reporting to line manager
- Drawing checking for correctness and quality compliance
- Model Review for clash check
- Guiding & Training junior designers for performance improvement
- Quality Conformance
- Drafting, Checking, Modelling & Coordination
- Other Skills:
- Bar Bending Schedule
- Quantity Estimation & Material take off
- Preparation of specification and data sheets.
- Preparation of sizing calculations.
- Preparation of TQs to Client in coordination with Principal Engineers.
- Review of detailed engineering calculations.
- Review of detailed engineering layouts.
- Review of load list.
- Preparation / review of cable schedule and MTO.
- Responsible for IDC and related documentation.
- Vendor offer review and preparation of TQs to Vendors.
- Participate in site visit for data collection and meetings.
- Attend IFAT / SAT for Electrical packages / equipments.
- Responsible for attending technical site queries during installation, pre commissioning and commissioning stage.
- Train and Mentor Engineers/Designers.
- Technical support for Designer/Draftsmen for preparation of layouts / modeling.
- Participate in all Trainings.
- Responsible for preparation of QMS documentation.
- Having the Basic & Detailed Engineering knowledge on the Design of Electrical Systems
- Having the adequate knowledge about Specification, Datasheets, Material requisitions, Bid evaluation, Purchase requisitions, review and approval of vendor documents for Electrical Equipments
- Possess basic knowledge on the Power System Analysis & Studies (ETAP or Equivalent)
- Possess basic knowledge on the 3D Model Review, Smart Plant Electrical, ACAD
- Possess basic knowledge on the Man-hour Estimates and control
- Possess adequate knowledge on the Quality Management systems
- Preparation of Overhead line specification / Design criteria for approval from Client.
- Preparation of scope of work for overhead line installation.
- Review the OHL Contractor / Sub - Contractor Vendor deliverables register (VDDR) and approval.
- Review the design calculations from OHL Contractor / Sub-Contractor and approval.
- Review the design and construction drawings from OHL Contractor / Sub-Contractor and approval.
- Review the BOQ / MTO from OHL Contractor / Sub-Contractor and approval.
- Review the Inspection and Test Plans from OHL Contractor / Sub-Contractor and approval.
- Preparation of TBE and vendor selection.
- Participate in the Factory Acceptance Tests of the major OHL equipment along with 3rd Party Inspectors and Client.
- Provide optimised design solutions for OHL systems in Projects and Proposals.
- Coordinate with other disciplines such as Civil, Pipe lines, Instrumentation for finalising tower foundations, communication systems etc.
- Participate and coordinate with Client personnel for approval of OHL design submitted by OHL Contractor / Sub-Contractor.
- Attend site queries and visit site for meetings to clear the technical queries raised.
- Providing technical support during OHL Installation, pre-commissioning and commissioning activities.
- Report to Lead Electrical Engineer / Project Engineering Manager / Project Manager on the status of OHL design. and engineering activities by OHL Contractor / Sub-Contractor and report delays.
- Participate in the Pre-Bid Engineering / Proposals activities such as preparation on MRs, review of offers, preparation of TBE related to OHL.
- Must have worked in design of OHL of 11kV and above
- Working knowledge on design of OHL system along with its accessories such as selection of switches, conductor design and selection, sag tension calculations, specific tower type selection for various sections / routes etc..,
- Working knowledge on Tower and OHL profiling for various terrains.
- Assess the quantities of OHL system and provide inputs to Procurement and Construction teams
- Inter-discipline coordination.
- PMC co-ordination.
- Should be conversant with: API / NFPA / Shell DEP / IEC / NEC / NEMA etc..
- Complete Knowledge on QMS and implementation.
- Study and complete understanding of Electrical design basis and equipment specifications.
- Preparation of Electrical load list.
- Preparation of standard design spread sheets for Calculations.
- Perform electrical design calculations and preparation of data sheets.
- Preparation of Detailed engineering Electrical layouts in coordination with Designers/Draftsmen.
- Preparation of Cable schedule & MTO.
- Participate in all Trainings.
- Responsible for QMS documentation.
- Having the Basic & Detailed Engineering knowledge on the Design of Electrical Systems.
- Having the adequate knowledge about Specification, Datasheets, Material requisitions, Bid evaluation, Purchase requisitions, review and approval of vendor documents for Electrical Equipments.
- Possess basic knowledge on the Power System Analysis & Studies (ETAP or Equivalent).
- Possess basic knowledge on the 3D Model Review, Smart Plant Electrical, ACAD.
- Possess basic knowledge on the Quality Management systems
- Supervise a team of engineers and designers in carrying out Instrument detailed engineering works and provide necessary technical procurement assistance in compliance with tender specifications/data sheets and within budgeted man-hour and project schedules.
- Well versed on MS-Office, Instrument sizing Software & Smart Plant Instrumentation (SPI).
- Having Basic knowledge on PLC/DCS/ESD programming softwares.
- Hands-on experience on 3D modelling review and Auto-CAD softwares
- Well aware about the Instrumentation & Controls related international standards and major end user specification requirements
- Operate as part of a team of engineers and designers in carrying out Instrument detailed engineering works and provide necessary technical procurement assistance in compliance with tender specifications/data sheets and within budgeted man-hour and project schedules.
- Well versed on MS-Office, Instrument sizing Software & Smart Plant Instrumentation (SPI).
- Having Basic knowledge on PLC/DCS/ESD programming softwares.
- Hands-on experience on 3D modelling review and Auto-CAD softwares
- Well aware about the Instrumentation & Controls related international standards and major end user specification requirements
- Operate as part of a team of Draftsperson and designers in carrying out Instrumentation and Telecom related Drawings
- Well versed on Auto CAD, PDS / PDMS / SP 3D, Smart plant Instrumentation (SPI), NAVIS & MS Office
During the detailed engineering phase the Employee will be based at Project Home Office in Middle East. Subsequently, some employee will have to move to Algeria for Field Engineering service, if required, when he will be provided single accommodation, food and local transport by the company.
- Job Duration: 12-15 months
- 1. Senior Design Engineer - Process (Material & Corrosion)
Qualification: B.E. / B.Tech in Metallurgy / Chemical / Mechanical engineering with sound knowledge in ECE / PREDICT etc. softwares.
Experience: 5 years and above, out of which minimum 3 years of experience in Design and Engineering of Oil & Gas / Refinery / Petrochemical plants. Main role is to perform Basic & Detailed engineering activities and develop / review of relevant material & corrosion engineering deliverables
Key responsibilities and Accountabilities:
Other Skills:
Conceptual engineering, Front-end engineering design (FEED), Technology evaluation, People management & Leadership skills, Simulation, Design Basis, Residual basic engineering, Detailed engineering activity, Adequacy check / Technical audit, Pre-commissioning & commissioning
Salary Range: AED 12500 - 14500 pm
2. Design Engineer - Process (Nos. 4)
Qualification: B.E. / B. Tech in Chemical Engineering, Basic knowledge in HYSYS / PIPESIM and well versed with MS Office.
Experience: 3 years and above, out of which minimum 2 years of experience in Process Design & Engineering of Oil & Gas / Refinery / Petrochemical plants/ Pipelines.
Key responsibilities and Accountabilities:
Front-end engineering design (FEED), Detailed engineering coordination, Awareness on 3D Modelling, Plot Plan, GA drawing, heat exchanger design, Knowing Algeria projects & standards will be added advantage.
Salary Range: AED 8500 - 10500 pm
3. Senior Design Engineer - Loss Prevention
Qualification: B.E. / B. Tech in Fire Protection, Safety engineering Chemical or Mechanical Engineering, or in similar Engineering field (Master Degree is Preferred)
Experience: 5 years and above, out of which minimum 3 years of experience in Design & Engineering of Oil & Gas / Refinery / Petrochemical plants.
Key responsibilities and Accountabilities:
PFD's, P&IDs, Process Data Sheets, Fire Fighting and safety Equipment Datasheets, Specification, Philosophys, Hydrant & Monitor location layout, Fire Fighting and Safety Equipment Layout, Escape Route and Safety Signs Layout, Passive Fire Protection Layout, Fire Water Line List, Fire & Gas Cause & Effect Matrix, Passive Fire Protection Schedule and Hazardous Area Classification Schedule etc, Oil & gas sector.
Salary Range: AED 12500 - 14500 pm
4. Sr. Design Engineer - Piping & Pipelines (Nos. 3)
Qualification: B.E. / B. Tech / M.E. / M. Tech - Mechanical / Production. AUTOCAD, MICROSTATION, CAESAR-II, PDS/PDMS/SP3D will be added advantage.
Experience: 5 years and above, out of which minimum 3 years of experience in Design & Engineering of Oil & Gas / Refinery / Petrochemical plants.
Key responsibilities and Accountabilities:
5. Designer - Piping & Pipelines (Nos. 2)
Qualification: Diploma / ITI in Mechanical with AUTOCAD, MICROSTATION and PDS/PDMS/SP3D.
Experience: 10 years and above, out of which out of which minimum 5 years of experience in Design & Engineering of Oil & Gas / Refinery / Petrochemical plants.
Key responsibilities and Accountabilities:
Job-specific skills required in:
6. Senior Design Engineer - Static & Packages Mechanical
Qualification: B.E. / B. Tech Mechanical, M.E. / M. Tech Mechanical
Experience: 8 years and above, out of which minimum 5 years of experience in Design and detailed Engineering of Oil & Gas / Refinery / Petrochemical plants. The role is perform design engineering activities per project requirements with focus on Quality and On-time delivery.
Key Responsibilities and Accountabilities:
7. Senior Design Engineer - HVAC
Qualification: B.E. / B. Tech Mechanical, M.E. / M. Tech Mechanical
Experience: 8 years and above, out of which minimum 5 years of experience in Design & Engineering of Oil & Gas / Refinery / Petrochemical plants.
Key Responsibilities and Accountabilities:
8. Senior Design Engineer - Civil & Structural (Nos. 4)
Qualification: BE / B. Tech / M.E / M. Tech Civil / Structural Engineering. STAAD PRO, Staad Foundation, MAT 3D, 3D model review software like Navisworks or SPR, Auto Cad
Experience: 5 years and above, out of which minimum 3 years of experience in Design & Engineering of Oil & Gas / Refinery / Petrochemical plants.
Key Responsibilities and Accountabilities:
Other Skills:
9. Design Engineer - Civil & Structural
Qualification: BE / B. Tech/ M.E / M. Tech Civil / Structural Engineering. STAAD PRO, Staad Foundation, MAT 3D, 3D model review software like Navisworks or SPR, Auto Cad
Experience: 3 years and above, out of which minimum 2 years of experience in Design & Engineering of Oil & Gas / Refinery / Petrochemical plants.
Key Responsibilities and Accountabilities:
Job-specific skills required:
10. Designer - Civil & Structural (Nos. 2)
Qualification: Diploma / ITI Civil / Mechanical. AutoCAD, X-Steel, PDS, PDMS, Micro station, Inventor, Tekla
Experience: 10 years and above, out of which minimum 5 years of experience in Civil & Structural Detailing in Oil & Gas / Hydrocarbon and Petrochemical Plants.
Key Responsibilities and Accountabilities:
11. Sr. Design Engineer - Electrical (Nos. 5)
Qualification: B.E. / B. Tech, M.E. / M. Tech Electrical & Electronics / Power Systems
Experience: 5 years and above, out of which minimum 3 years of experience in Design & Engineering of Oil & Gas / Refinery / Petrochemical plants. The role is to carry out Design and Detailed engineering of Documents and Drawings from concept to completion for deliverables.
Key responsibilities and Accountabilities:
12. Senior Design Engineer - Overhead Lines (OHL)
Qualification: B.E. / B. Tech, M.E. / M. Tech Electrical
Experience: 10 years and above experience in Engineering field, out of which minimum 5 years in the design and development of Over Head Line Systems (OHL) in oil & gas industry / Power / Petro Chemical / Chemical industry.
Key responsibilities and Accountabilities:
13. Design Engineer - Electrical (Nos. 3)
Qualification: B.E. / B. Tech, M.E. / M. Tech Electrical & Electronics / Power Systems
Experience: 3 years and above, out of which minimum 2 years of experience in Design & Engineering of Oil & Gas / Refinery / Petrochemical plants.
Key responsibilities and Accountabilities:
14. Senior Design Engineer Instrumentation (Nos. 2)
Qualification: B.E. / B. Tech, M.E. / M. Tech Instrumentation / Control
Experience: 7 years and above, out of which minimum 3 years of experience in Detail Engineering of Oil & Gas / Refinery / Petrochemical projects in the EPCs.
Key responsibilities and Accountabilities:
15. Design Engineer - Instrumentation
Qualification: B.E. / B. Tech, M.E. / M. Tech Instrumentation / Control
Experience: 3 years and above, out of which minimum 2 years of experience in Detail Engineering of Oil & Gas / Refinery / Petrochemical projects in the EPCs.
Key responsibilities and Accountabilities:
16. Draftsman / Designer - Instrumentation
Qualification: Diploma in Instrumentation / Electrical
Experience: 5 - 10 years of experience in Oil & Gas industry.
Key responsibilities and Accountabilities:
Salary Range: AED 4500 - 6500 pm
Terms and Conditions:
Status of Employment: Single
Accommodation, Food and Transportation will require to be organised by the employee at his own cost while at Project Home Office in the Middle East.
There is no overtime provision.
Probation Period: 90 days
Medical Insurance: Provided by Company
Annual Leave: 30 days
Air Ticket for Annual Leave: One Economy Class Air Ticket per year up to the nearest international airport of the employee hometown.
Prospective candidates meeting the above requirements and interested in this opening and readily available for early joining, may please send their application with updated CV and all relevant supporting documents viz. scanned copy of degree/diploma, testimonials / service certificates and current salary slip to justify their claims for suitability for this position, to smitap@tyson-enterprises.com and tysonteam@gmail.com
Post a Comment