Any Nationality
Own plant process designs, interface with other Engineering disciplines, support projects and proposals
Tasks and responsibilities
The process Engineer shall be responsible for, but not limited to, the following:
• Provide inputs to the project and proposals teams with regard to all aspects of process engineering
• Review contract specification and request process design information If necessary
• Perform process simulations and develop process flow diagrams (PFDs) and Heat and Material balances
• Perform design optimisation in tandem with a cost benefit analysis incorporating capital and installation cost estimates.
• Carry out sizing calculations for process equipment and provide the information in the form of equipment data sheets.
• Prepare material selection designation for plant requirements
• Develop line sizes and hydraulic calculations such as pressure drop and Pump NPSH.
• Prepare P&IDs, valve lists, line lists, equipment lists and instrument lists
• Generate process control philosophies
• Produce logic diagrams, cause and effect charts for power plant auxiliary systems such as firefighting, fuel supply etc.
• Review Design and sizing of safety relief valves, gas fuel ESDs
• Define mechanical design conditions for equipment and piping components
• Participate in HAZOP studies
• Review system operating manuals and commissioning plans
• Support site start-up and performance testing as required
• Verify subcontractor/supplier Process designs, documents and request information such as stream data etc. where applicable.
• Use creative and innovative conceptual designs to ensure proposals are cost competitive
Education and Experience
• BE or BSc in Chemical engineering or Mechanical engineering, though Chemical Engineering is preferred.
• 4-6 Years relevant design experience is required
• A good application of control & instrumentation is required
• Experience in process simulation is a must
• Experience in Oil & Gas or Gas Turbine Power plant projects is preferred.
• Experience with fuel supply systems or water treatment is preferred
• A good understanding of process safety requirements is preferred.
Skills:
• A strong working knowledge of process and flow simulators such as HYSYS, Pipeflow, PipeSim, Aspen Basic Engineering (ABE) or equivalents
• Intermediate to advanced level user of MS office platform with special emphasis on MS EXCEL
• Detail orientated
• Ability to analyse and solve problems
• Creative
• Effective at communicating process concepts to project teams, clients etc.
Philip varkey
info@urukgroup.com
Own plant process designs, interface with other Engineering disciplines, support projects and proposals
Tasks and responsibilities
The process Engineer shall be responsible for, but not limited to, the following:
• Provide inputs to the project and proposals teams with regard to all aspects of process engineering
• Review contract specification and request process design information If necessary
• Perform process simulations and develop process flow diagrams (PFDs) and Heat and Material balances
• Perform design optimisation in tandem with a cost benefit analysis incorporating capital and installation cost estimates.
• Carry out sizing calculations for process equipment and provide the information in the form of equipment data sheets.
• Prepare material selection designation for plant requirements
• Develop line sizes and hydraulic calculations such as pressure drop and Pump NPSH.
• Prepare P&IDs, valve lists, line lists, equipment lists and instrument lists
• Generate process control philosophies
• Produce logic diagrams, cause and effect charts for power plant auxiliary systems such as firefighting, fuel supply etc.
• Review Design and sizing of safety relief valves, gas fuel ESDs
• Define mechanical design conditions for equipment and piping components
• Participate in HAZOP studies
• Review system operating manuals and commissioning plans
• Support site start-up and performance testing as required
• Verify subcontractor/supplier Process designs, documents and request information such as stream data etc. where applicable.
• Use creative and innovative conceptual designs to ensure proposals are cost competitive
Education and Experience
• BE or BSc in Chemical engineering or Mechanical engineering, though Chemical Engineering is preferred.
• 4-6 Years relevant design experience is required
• A good application of control & instrumentation is required
• Experience in process simulation is a must
• Experience in Oil & Gas or Gas Turbine Power plant projects is preferred.
• Experience with fuel supply systems or water treatment is preferred
• A good understanding of process safety requirements is preferred.
Skills:
• A strong working knowledge of process and flow simulators such as HYSYS, Pipeflow, PipeSim, Aspen Basic Engineering (ABE) or equivalents
• Intermediate to advanced level user of MS office platform with special emphasis on MS EXCEL
• Detail orientated
• Ability to analyse and solve problems
• Creative
• Effective at communicating process concepts to project teams, clients etc.
Philip varkey
info@urukgroup.com
No comments:
Post a Comment
Please give your feedback or Job Request here